Browsing by Author "Visconte, Leila"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Silica sol obtained from rice husk ash(Publishing House of Lviv Polytechnic National University, 2009) de Sousa, Ana Maria; Visconte, Leila; Mansur, Claudia; Furtado, CristinaRice husk ash was used to produce sodium silicate with SiO2/Na2O=3. The investigation of NaOH concentration and temperature on the silica conversion showed that NaOH has positive influence. SiO2/Na2O - 3 was produced with 0.8 mol/l of NaOH and 403/453 K. These solutions were used to produce silica sol with diameter of - 5nm. Одержано силікат натрію з співвідношенням SiO2/Na2O = 3 із золи рисової лузги. Вивчено вплив концентрації NaOH та температури на перетворення кремнію та показано, що NaOH позитивно впливає на утворення силікату натрію. Si O 2/Na2O= 3 був одержаний при 403–423 К, виходячи із концентрації NaOH 0.8 моль/ л. Запропоновані розчини використані для отримання кремнієвого золю з діаметром частинок ∼ 5 нм.Item The evaluation of bis(4-ethylphenylsulfonyldithiocarbimato)zincate (II) (ZNIBU) activity in the vulcanization of NBR compounds and its effect on their mechanical properties(Publishing House of Lviv Polytechnic National University, 2010) de Oliveira, Iara; Cunha, Leandro; Visconte, Leila; Oliveira, Marcelo; Rubinger, MayuraThe effect of accelerator type on the vulcanization process and mechanical properties of nitrile rubber (NBR) compounds was investigated. Three commercial accelerators were selected, N-N-t-butyl-2- benzothiazole sulfenamide (TBBS), tetramethylthiuram disulfide (TMTD) and bis(dimethyldithiocarbamato)zinc (II) (ZDMC) and compared with the compound bis(4methylphenylsulfonyldithiocarbimato)zincate (II) (ZNIBU). Surprisingly, it was found that the optimum vulcanization time for ZNIBU showed better results than for TBBS. Вивчено вплив природи прискорювача вулканізації на перебіг процесу і механічні властивості нітрилових каучуків (НК). Проведено порівняння N, N-трет-бутил-2-бензотіазолсульфенаміду, дисульфіду тетраметилтиураму та біс(диметилдитіокарбамато)цинкату (ІІ) з біс(4-метилфенілсульфонілдітіокарбімато)цинкатом (ІІ). Встановлено, що оптимальний час вулканізації досягається на досліджуваному прискорювачі.Item TPU/Mica composites prepared in torque rheometer: processability, mechanical properties and vorphology(Publishing House of Lviv Polytechnic National University, 2011) Escocio, Viviane; Altstadt, Volker; Visconte, Leila; de Carvalho, Mariana; Nunes, ReginaThis work is concerned with the preparation of thermoplastic polyurethane elastomer (TPU) composites with mica, and their characterization as for processability, mechanical and thermal properties and morphology behavior. The amount of added mica varied from 0 to 20 phr and the results showed few interactions between mica and the polymer matrix. Processability is facilitated by the increasing amount of mica but TPU upon strain crystallizability, as well as Tg, decrease with the increase in mica content. The main interest in using mica is the evaluation of a low cost mineral as a reinforcing material for the engineering polymer TPU. Описаний процес підготовки композитів термопластичного поліуретанового еластомеру (ТПУ) з слюдою, та наведені такі їх характеристики, як технологічність, механічні та теплові властивості і морфологія. Кількість доданої слюди змінювалась від 0 до 20 мас.част. Показана взаємодія між слюдою і полімерною матрицею. Встановлено, що збільшення кількості слюди сприяє технологічності процесу, але при цьому зменшується напруження кристалізованості та температура склування. Показано, що низька вартість мінералу як укріплюю чого матеріалу для технічного полімеру ТПУ є критерієм оцінювання.