Ukrainian Journal of Mechanical Engineering and Materials Science. – 2019. – Vol. 5, No. 3/4

Permanent URI for this collectionhttps://ena.lpnu.ua/handle/ntb/57178

Науковий журнал

Засновник і видавець Національний університет «Львівська політехніка». Виходить двічі на рік з 2015 року.

Ukrainian Journal of Mechanical Engineering and Materials Science = Український журнал із машинобудування і матеріалознавства : науковий журнал / Lviv Politechnic National University ; editor-in-chief Oleksiy Lanets . – Lviv : Lviv Politechnic Publishing House, 2019. – Volume 5, number 3/4. – 88 p.

Browse

Author: search.filters.author.Kusyi YaroslavHas files: Yes

Search Results

Now showing 1 - 2 of 2
  • Thumbnail Image
    Item
    Modeling of “combined cutter - cone” connection in tricone drill bits
    (Lviv Politechnic Publishing House, 2019) Slipchuk Andrii; Kuk Andrii; Kusyi Yaroslav
    A theoretical analysis of the stiffness of the “cutter-cone” connection was performed. In the article the character and magnitude of the tension at the contact of "cutter-cone" are investigated. An analysis of the surface of the openings for carbide inserts revealed traces of plastic deformation and fretting wear. Since the contact bond of the cutter with the body of cone is the only factor that provides the strength of the connection, let consider the effect of mechanical properties of the cones body and a cutter on the magnitude of the forces of contact and tension in the connection. The surface of the shaft of this design consists of equal parts of solid alloy and steel. If you make a ring at a smaller diameter of the shank of a carbide cutter, this will increase the reliability of the connection of the insertion with the body of the rock cutting tool, optimize toughness of cutter fastening, and ensure high stability of the hard-alloyed inset cutter before fracture. As a result of the conducted researches, a qualitative correlation between the hardness of the carbide insertion fastening in the holes of cone and the nature of the destruction of the carbide cutters has been established. Due to the conducted research, the character of the distribution of contact tensions in the conjugated areas “combined cutter - a hole of cone” was established. The theme of the development of new rational constructions of rock-destructive equipment of cones, rock-destructive inserts, schemes of its effective arrangement on the brushes of cone is still actual. A separate issue of further research is the study of functional and energy interaction of elements of propulsion and rock-destructive equipment.
  • Thumbnail Image
    Item
    Development of the finishing and strengthening technological operations using SADT-technologies
    (Lviv Politechnic Publishing House, 2019) Kusyi Yaroslav; Lychak Oleh; Topilnytskyy Volodymyr; Bošanský Miroslav
    The rational design of technological processes of parts manufacturing in single and small-scale production is inefficient without wide introduction of modern tools of part manufactu ring automation with modern computer-based equipment and software. It is desirable to carry out of automated synthesis of single route technological processes with minimal influence of the operator on the technological environment. The technology of computer-aided design of technological processes is used to develop effective algorithms of functioning of adapted systems for control of technological processes and their mplementation when taking into account interrelations with the technological environment. Automated development of technological environments of a given level of design concerning a dedicated technical system is possible on the basis of their rational functional models, created by means of CALS-technologies. The rational use of the SADT methodology with application of the principle of decomposition and development of the SADT-diagrams allows to solve the given technical problems. Therefore, the purpose of this paper is to develop and study the vibrational centrifugal surface strengthening at the finishing and hardening technological operation to provide the required quality parameters and operational characteristics of the parts. The object of this research is a finishing and hardening technological operation. The subject of this research is method and parameters of vibrational-centrifugal surface strengthening to provide the required quality parameters and operational characteristics of the parts. The development of SADT diagrams allows to divide the technological process to technological operations, cutter–setting positions, technological steps, main machining steps etc. In this paper the principles of control of technological operation for vibration-centrifugal strengthening of surfaces of parts are suggested. The experimental device for machining of inner surfaces of parts is described. The initial and detailed model of the operation of the vibrational-centrifugal strengthening is offered. Statistical and structural analysis of technological process made it possible to establish the influence of the parameters of the vibrational-centrifugal strengthening on the geometric and physical mechanical parameters of the surface quality and associated operational characteristics. Further research in that field will be related on the development of practical recommendations for using of the vibrational centrifugal surface treatment for improving of the geometric and physical and mechanical parameters of parts surfaces.