Вісники та науково-технічні збірники, журнали
Permanent URI for this communityhttps://ena.lpnu.ua/handle/ntb/12
Browse
2 results
Search Results
Item Design – technological optimization of the level of residual deformations during welding of pipe sections from PT-7m alloy(Lviv Politechnic Publishing House, 2021) Biloborodchenko, Volodymyr; Dzyubyk, Andrij; Dzyubyk , Liudmyla; Lviv Polytechnic National UniversityApplication of tubular elements in the chemical industry is widely used. The special properties of materials and their reaction to the welding thermal cycle is quite complex. This is especially true of titanium alloys, which when heated are sensitive to environmental influences, require special welding techniques and undergo residual welding deformations. The welded joints of tubular elements made of titanium alloy brand PT-7m, which undergo transverse deformations due to welding, are studied. It is necessary to ensure high-quality sealed welds. Analysis of the literature has shown that to obtain a guaranteed penetration it is necessary to increase the power of the arc discharge or perform multi-pass welding. This will provide larger cross sections of welded parts and should provide the specified strength characteristics. However, this technology, in turn, leads to an increase in residual deformation in the vicinity of the welded joint due to the intensive increase in the coefficient of linear expansion when heating the material. Also, the special thermophysical properties of titanium alloy such as increasing the affinity for gases when heated, increasing the grain size lead to a decrease in strength properties. In the presented work it is proposed to use a mechanical angular deformer with an indicator head and a reference base for the study of transverse residual deformations. Peculiarities of measuring sockets and methods of their preparation are revealed. A calculation scheme for determining the amount of deformation has been developed, which has been tested on flat welded specimens and transferred to tubular elements. The sequence of deformation measurement process is described and the peculiarities of their formation on flat samples and tubular sections are studied. The constructive decision of a welded joint of pipes which provides use of a compensation ring is offered. This approach allows to provide reliable protection of the root of the seam and its optimal formation with minimal residual deformation. At the same time it is possible to reach the reproducible form of a dagger of similar penetration in one pass. The result is a welded joint of the lock type, which is sealed and has a free formation of the seam root with high-quality protection by the gas atmosphere. The use of pulsed arc welding with a non-fusible electrode in an argon environment with filler wire allows to minimize the thermal impact on the base metal. Statistical processing of experimental data on the parameters of the welding mode and their influence on the residual transverse welding deformations is carried out. To obtain an unambiguous statistically reliable answer about the valid law of distribution of experimental data of the results of strain measurement, the balancing procedure and the development of an analytical pproximation distribution model are involved. It is shown that the measured values of the residual transverse deformation of the welded assembly are correctly described by the Laplace distribution, which predicts (probability not worse than 90 %) a decrease in the average value of the deformation value by 1.3 times.Item Features of repair welding of power hydrocylinder elements(Lviv Politechnic Publishing House, 2020) Dzyubyk, Andrij; Nazar, Ihor; Dzyubyk , Liudmyla; Lviv Polytechnic National UniversityAt present, the use of power hydraulic cylinders is an integral part of most industrial equipment. They provide translational and horizontal movements, replacement of goods, fixation, etc. These devices are necessary elements of the equipment where application of the corresponding level of effort is applied. Often hydraulic cylinders are created specialized to perform certain types of work. It should be noted that part of the elements of the power cylinder in the manufacture is combined with welding. Such integral connections provide rigidity of installation, tightness of a design, fatigue strength at multicycle loadings. Difficult operating conditions, significant workloads, the presence of various external factors often leads to the destruction of individual elements of the cylinder. At the same time, the cost of repairing equipment that involves replacement with new power devices is quite high. This causes the implementation of repair and restoration work carried out at specialized enterprises. However, in the case of repairs, there are often a number of problems that require prompt resolution in the production environment. These should include the provision of basic materials with similar physical and chemical properties, the establishment of welding modes, the selection of the necessary welding materials, the use of appropriate techniques for conducting the arc process, etc. Therefore the repaired welded design of the case of the power hydraulic cylinder needs additional studying for weldability of separate elements among themselves, formation of a zone of thermodeformation influence. In general, the repaired hydraulic cylinder should meet the installation operating requirements depending on the purpose. The design of the considered hydraulic cylinder of the press installation is rather technological from the point of view of maintenance of automation of welding process. It contains long welds of a simple ring configuration. At the same time, the significant linear dimensions and the presence of a cylindrical surface cause some complexity in the implementation of processes. The construction material of the power hydraulic cylinder is low-carbon low-alloy steels. The analysis of technological weldability indicates a tendency to crack due to the thermal cycle of welding. The simulation of welds of the power hydraulic cylinder is performed in the work. The number of rollers was taken into account when obtaining butt welds. A compa ative analysis of different electrode materials with different doping systems is done. The most applicable welding materials by chemical composition and properties of the weld metal are determined. According to the literature data and the results of comparative analysis, the optimal range of cooling rate of the main material of the hydraulic cylinder was established. The properties and structure of the zone of thermal influence of the butt welds of the power hydraulic cylinder have been studied. The magnitude of deformations and stresses caused by the thermal cycle of welding of the hell structure of the hydraulic cylinder liner is investigated. The admissible parameters of the zone of plastic deformations during butt welding are determined.