Adjusting the Performance Properties of Products Obtained by Injection Molding from Polyamide 12

Simple item page
dc.citation.epage845
dc.citation.issue4
dc.citation.spage836
dc.contributor.affiliationKOSTAL Ukraine TOV
dc.contributor.authorPrystynskyi, Serhii
dc.coverage.placenameЛьвів
dc.coverage.placenameLviv
dc.date.accessioned2025-03-05T08:54:10Z
dc.date.created2023-02-28
dc.date.issued2023-02-28
dc.description.abstractДосліджено та показано вплив параметрів технологічного процесу на стійкість до агресивного середовища (етилового спирту С2Н5ОН) пластикових деталей, які були отримані методом лиття пластмас під тиском з полімерного композиційного матеріалу поліаміду 12 (РА12).
dc.description.abstractThe influence of technological process parameters on the resistance to an aggressive environment (ethyl alcohol С2Н5ОН) of plastic parts obtained by injection molding from the polymer composite material polyamide 12 (РА12) was studied and shown.
dc.format.extent836-845
dc.format.pages10
dc.identifier.citationPrystynskyi S. Adjusting the Performance Properties of Products Obtained by Injection Molding from Polyamide 12 / Serhii Prystynskyi // Chemistry & Chemical Technology. — Lviv : Lviv Politechnic Publishing House, 2023. — Vol 17. — No 4. — P. 836–845.
dc.identifier.citationenPrystynskyi S. Adjusting the Performance Properties of Products Obtained by Injection Molding from Polyamide 12 / Serhii Prystynskyi // Chemistry & Chemical Technology. — Lviv : Lviv Politechnic Publishing House, 2023. — Vol 17. — No 4. — P. 836–845.
dc.identifier.doidoi.org/10.23939/chcht17.04.836
dc.identifier.urihttps://ena.lpnu.ua/handle/ntb/63694
dc.language.isoen
dc.publisherВидавництво Львівської політехніки
dc.publisherLviv Politechnic Publishing House
dc.relation.ispartofChemistry & Chemical Technology, 4 (17), 2023
dc.relation.references[1] Al-Maadeed, M.A.A.; Ponnamma, D.; El-Samak, A.A. Polymers to improve the world and lifestyle: physical, mechanical, and chemical needs. In Polymer Science and Innovative Applications. Materials, Techniques, and Future Developments; Elsevier Inc., 2020; pp 1–19. https://doi.org/10.1016/B978-0-12-816808-0.00001-9
dc.relation.references[2] Baillie, C.; Peijs, T. Chapter 7 - The Land of Polymers. In Navigating the Materials World A Guide to Understanding Materials Behavior; Baillie, C.; Vanasupa, L., Eds.; Academic Press, 2003; pp 135–159. https://doi.org/10.1016/B978-012073551-8/50008-8
dc.relation.references[3] Kabat, O.; Sytar, V.; Derkach, O.; Sukhyy, K. Polymeric Composite Materials of Tribotechnical Purpose with a High Level of Physical, Mechanical and Thermal Properties. Chem. Chem. Technol. 2021, 15, 543–550. https://doi.org/10.23939/chcht15.04.543
dc.relation.references[4] Khosravani, M.R.; Nasiri, S. Injection Molding Manufacturing Process: Review of Case-Based Reasoning Applications. J Intell Manuf 2020, 31, 847–864. https://doi.org/10.1007/s10845-019-01481-0
dc.relation.references[5] Hellmann, W.; Marino, D.; Megahed, M.; Suggs, M.; Borowski, J.; Negahban, A. Human, AGV or AIV? An integrated Framework for Material Handling System Selection with Real-World Application in an Injection Molding Facility. Int. J. Adv. Manuf. Technol. 2019, 101, 815–824. https://doi.org/10.1007/s00170-018-2958-x
dc.relation.references[6] Pervez, H.; Mozumder, M.S.; Mourad, A-H.I. Optimization of Injection Molding Parameters for HDPE/TiO2 Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis. Materials 2016, 9, 710. https://doi.org/10.3390/ma9080710
dc.relation.references[7] Chen, W.C.; Fu, G.L.; Kurniawan, D. A Two-Stage Optimization System for the Plastic Injection Molding with Multiple Performance Characteristics. Adv Mat Res 2012, 468-471, 386-390. https://doi.org/10.4028/www.scientific.net/AMR.468-471.386
dc.relation.references[8] Huang, W.T.; Tsai, C.L.; Ho, W.H.; Chou, J.H. Application of Intelligent Modeling Method to Optimize the Multiple Quality Characteristics of the Injection Molding Process of Automobile Lock Parts. Polymers 2021, 13, 2515. https://doi.org/10.3390/polym13152515
dc.relation.references[9] Sánchez‐Safont, E.L.; Arrillaga, A.; Anakabe, J.; Gamez‐Perez, J.; Cabedo, L., PHBV/TPU/cellulose Compounds for Compostable Injection Molded Parts with Improved Thermal and Mechanical Performance. J. Appl. Polym. Sci. 2019. 136, 47257. https://doi.org/10.1002/app.47257
dc.relation.references[10] Haider, T.P.; Völker, C.; Kramm, J.; Landfester, K.; Wurm, F.R. Plastics of the Future? The Impact of Biodegradable Polymers on the Environment and on Society. Angew. Chem. Int. Ed. 2019, 58, 50–62. https://doi.org/10.1002/anie.201805766
dc.relation.references[11] Serrano-Ruiz, H.; Martin-Closas, L.; Pelacho, A.M. Biodegradable Plastic Mulches: Impact on the Agricultural Biotic Environment. Sci. Total Environ. 2021, 750, 141228. https://doi.org/10.1016/j.scitotenv.2020.141228
dc.relation.references[12] Roda, A.; Matias, A.A.; Paiva, A.; Duarte, A.R.C. Polymer Science and Engineering Using Deep Eutectic Solvents. Polymers 2019, 11, 912. https://doi.org/10.3390/polym11050912
dc.relation.references[13] Mabesoone, M.F.J.; Palmans, A.R.A.; Meijer, E.W. Solute-Solvent Interactions in Modern Physical Organic Chemistry: Supramolecular Polymers as a Muse. J. Am. Chem. Soc. 2020, 142, 19781–19798. https://doi.org/10.1021/jacs.0c09293
dc.relation.references[14] Laurati, M.; Arbe, A.; De Anda A.R.; Fillot, L.A.; Sotta, P. Effect of Polar Solvents on the Crystalline Phase of Polyamides. Polymer 2014, 55, 2867–2881. https://doi.org/10.1016/j.polymer.2014.04.031
dc.relation.references[15] Bratychak Jr., M.; Zemke, V.; Chopyk, N. The Features of Rheological and Tribological Behavior of High-Viscosity Polyolefine Compositions Depending on Their Content. Chem. Chem. Technol. 2021, 15, 486–492. https://doi.org/10.23939/chcht15.04.486
dc.relation.references[16] Spina, R. Optimisation of Injection Moulded Parts by Using ANN-PSO Approach. J. Achiev. Mater. Manuf. Eng. 2006, 15, 146–152.
dc.relation.references[17] Hopmann, Ch.; Reßmann, A.; Heinisch, J. Influence on Product Quality by pvT-Optimised Processing in Injection Compression Molding. Int Polym Process 2016, 31, 156-165. https://doi.org/10.3139/217.3058
dc.relation.references[18] Rosli, M.U.; Khor, C.Y.; Nawi, M.A.M.; Mohamad, N.S.; Zakaria, M.S. Minimizing Warpage and Shrinkage of Plastic Car Rear Bumper Fabrication via Simulation Based Optimisation. J Phys Conf Ser 2021, 2051, 012012. https://doi.org/10.1088/1742-6596/2051/1/012012
dc.relation.references[19] Gómez‐Monterde, J.; Sánchez‐Soto, M.; Maspoch, M.L. Influence of Injection Molding Parameters on the Morphology, Mechanical and Surface Properties of ABS Foams. Adv. Polym. Technol. 2018, 37, 2707–2720. https://doi.org/10.1002/adv.21944
dc.relation.references[20] Wang, J.; Mao, Q.; Jiang, N.; Chen, J. Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites. Polymers 2022, 14, 23. https://doi.org/10.3390/polym14010023
dc.relation.references[21] Xie, P.; Chen, J.; Ye, B.; Wang, R.; Dang, K.; Yang, W.; Ostrikov, K. Plasma Sprayed Thermal Barrier Coatings: Effects of Polyamide Additive on Injection Molding Part Quality. J. Appl. Polym. Sci. 2022, 139, 51980. https://doi.org/10.1002/app.51980
dc.relation.references[22] Weiland, J.; Dittmar, H.; Beier, C.J.; Ramesh, C.; Marx, B.; Schiebahn, A.; Jaeschke, P.; Overmeyer, L.; Reisgen, U.,. Improvement of the Adhesive Bonding Properties of an Polyamide 6 Injection Molded Fiber Reinforced Plastic Component by Laser Beam Pre-Treatment. Proceedings of the Institution of Mechanical Engineers. P I MECH ENG D-J AUT 2021, 235, 3243–3255. https://doi.org/10.1177/0954407020976195
dc.relation.references[23] Levytskyi, V.; Masyuk, A.; Katruk, D.; Kuzioła, R.; Bratychak Jr., M.; Chopyk, N.; Khromyak, U. Influence of Polymer-Silicate Nucleator on the Structure and Properties of Polyamide 6. Chem. Chem. Technol. 2020, 14, 496-503. https://doi.org/10.23939/chcht14.04.496
dc.relation.references[24] Meng, C.; Liu, X. Micro and Macro Analysis of Physicochemical Properties of Bio-Based Semi-Aromatic High Temperature Polyamide PA5T/56. POLYM-PLAST TECH MAT 2022, 61, 1118–1129. https://doi.org/10.1080/25740881.2022.2039186
dc.relation.references[25] Prystynskyi, S.; Budash, Yu.; Plavan, V.; Shuliak, R. Vplyv osnovnykh tekhnolohichnykh parametriv na stabilnist protsesu lyttia pid tyskom multykomponentnykh vidkhodiv polimernykh kompozytsii. Tekhnichni nauky i tekhnolohii 2023, 4, 148–-157. https://doi.org/10.25140/2411-5363-2022-4(30)-148-157
dc.relation.referencesen[1] Al-Maadeed, M.A.A.; Ponnamma, D.; El-Samak, A.A. Polymers to improve the world and lifestyle: physical, mechanical, and chemical needs. In Polymer Science and Innovative Applications. Materials, Techniques, and Future Developments; Elsevier Inc., 2020; pp 1–19. https://doi.org/10.1016/B978-0-12-816808-0.00001-9
dc.relation.referencesen[2] Baillie, C.; Peijs, T. Chapter 7 - The Land of Polymers. In Navigating the Materials World A Guide to Understanding Materials Behavior; Baillie, C.; Vanasupa, L., Eds.; Academic Press, 2003; pp 135–159. https://doi.org/10.1016/B978-012073551-8/50008-8
dc.relation.referencesen[3] Kabat, O.; Sytar, V.; Derkach, O.; Sukhyy, K. Polymeric Composite Materials of Tribotechnical Purpose with a High Level of Physical, Mechanical and Thermal Properties. Chem. Chem. Technol. 2021, 15, 543–550. https://doi.org/10.23939/chcht15.04.543
dc.relation.referencesen[4] Khosravani, M.R.; Nasiri, S. Injection Molding Manufacturing Process: Review of Case-Based Reasoning Applications. J Intell Manuf 2020, 31, 847–864. https://doi.org/10.1007/s10845-019-01481-0
dc.relation.referencesen[5] Hellmann, W.; Marino, D.; Megahed, M.; Suggs, M.; Borowski, J.; Negahban, A. Human, AGV or AIV? An integrated Framework for Material Handling System Selection with Real-World Application in an Injection Molding Facility. Int. J. Adv. Manuf. Technol. 2019, 101, 815–824. https://doi.org/10.1007/s00170-018-2958-x
dc.relation.referencesen[6] Pervez, H.; Mozumder, M.S.; Mourad, A-H.I. Optimization of Injection Molding Parameters for HDPE/TiO2 Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis. Materials 2016, 9, 710. https://doi.org/10.3390/ma9080710
dc.relation.referencesen[7] Chen, W.C.; Fu, G.L.; Kurniawan, D. A Two-Stage Optimization System for the Plastic Injection Molding with Multiple Performance Characteristics. Adv Mat Res 2012, 468-471, 386-390. https://doi.org/10.4028/www.scientific.net/AMR.468-471.386
dc.relation.referencesen[8] Huang, W.T.; Tsai, C.L.; Ho, W.H.; Chou, J.H. Application of Intelligent Modeling Method to Optimize the Multiple Quality Characteristics of the Injection Molding Process of Automobile Lock Parts. Polymers 2021, 13, 2515. https://doi.org/10.3390/polym13152515
dc.relation.referencesen[9] Sánchez‐Safont, E.L.; Arrillaga, A.; Anakabe, J.; Gamez‐Perez, J.; Cabedo, L., PHBV/TPU/cellulose Compounds for Compostable Injection Molded Parts with Improved Thermal and Mechanical Performance. J. Appl. Polym. Sci. 2019. 136, 47257. https://doi.org/10.1002/app.47257
dc.relation.referencesen[10] Haider, T.P.; Völker, C.; Kramm, J.; Landfester, K.; Wurm, F.R. Plastics of the Future? The Impact of Biodegradable Polymers on the Environment and on Society. Angew. Chem. Int. Ed. 2019, 58, 50–62. https://doi.org/10.1002/anie.201805766
dc.relation.referencesen[11] Serrano-Ruiz, H.; Martin-Closas, L.; Pelacho, A.M. Biodegradable Plastic Mulches: Impact on the Agricultural Biotic Environment. Sci. Total Environ. 2021, 750, 141228. https://doi.org/10.1016/j.scitotenv.2020.141228
dc.relation.referencesen[12] Roda, A.; Matias, A.A.; Paiva, A.; Duarte, A.R.C. Polymer Science and Engineering Using Deep Eutectic Solvents. Polymers 2019, 11, 912. https://doi.org/10.3390/polym11050912
dc.relation.referencesen[13] Mabesoone, M.F.J.; Palmans, A.R.A.; Meijer, E.W. Solute-Solvent Interactions in Modern Physical Organic Chemistry: Supramolecular Polymers as a Muse. J. Am. Chem. Soc. 2020, 142, 19781–19798. https://doi.org/10.1021/jacs.0c09293
dc.relation.referencesen[14] Laurati, M.; Arbe, A.; De Anda A.R.; Fillot, L.A.; Sotta, P. Effect of Polar Solvents on the Crystalline Phase of Polyamides. Polymer 2014, 55, 2867–2881. https://doi.org/10.1016/j.polymer.2014.04.031
dc.relation.referencesen[15] Bratychak Jr., M.; Zemke, V.; Chopyk, N. The Features of Rheological and Tribological Behavior of High-Viscosity Polyolefine Compositions Depending on Their Content. Chem. Chem. Technol. 2021, 15, 486–492. https://doi.org/10.23939/chcht15.04.486
dc.relation.referencesen[16] Spina, R. Optimisation of Injection Moulded Parts by Using ANN-PSO Approach. J. Achiev. Mater. Manuf. Eng. 2006, 15, 146–152.
dc.relation.referencesen[17] Hopmann, Ch.; Reßmann, A.; Heinisch, J. Influence on Product Quality by pvT-Optimised Processing in Injection Compression Molding. Int Polym Process 2016, 31, 156-165. https://doi.org/10.3139/217.3058
dc.relation.referencesen[18] Rosli, M.U.; Khor, C.Y.; Nawi, M.A.M.; Mohamad, N.S.; Zakaria, M.S. Minimizing Warpage and Shrinkage of Plastic Car Rear Bumper Fabrication via Simulation Based Optimisation. J Phys Conf Ser 2021, 2051, 012012. https://doi.org/10.1088/1742-6596/2051/1/012012
dc.relation.referencesen[19] Gómez‐Monterde, J.; Sánchez‐Soto, M.; Maspoch, M.L. Influence of Injection Molding Parameters on the Morphology, Mechanical and Surface Properties of ABS Foams. Adv. Polym. Technol. 2018, 37, 2707–2720. https://doi.org/10.1002/adv.21944
dc.relation.referencesen[20] Wang, J.; Mao, Q.; Jiang, N.; Chen, J. Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites. Polymers 2022, 14, 23. https://doi.org/10.3390/polym14010023
dc.relation.referencesen[21] Xie, P.; Chen, J.; Ye, B.; Wang, R.; Dang, K.; Yang, W.; Ostrikov, K. Plasma Sprayed Thermal Barrier Coatings: Effects of Polyamide Additive on Injection Molding Part Quality. J. Appl. Polym. Sci. 2022, 139, 51980. https://doi.org/10.1002/app.51980
dc.relation.referencesen[22] Weiland, J.; Dittmar, H.; Beier, C.J.; Ramesh, C.; Marx, B.; Schiebahn, A.; Jaeschke, P.; Overmeyer, L.; Reisgen, U.,. Improvement of the Adhesive Bonding Properties of an Polyamide 6 Injection Molded Fiber Reinforced Plastic Component by Laser Beam Pre-Treatment. Proceedings of the Institution of Mechanical Engineers. P I MECH ENG D-J AUT 2021, 235, 3243–3255. https://doi.org/10.1177/0954407020976195
dc.relation.referencesen[23] Levytskyi, V.; Masyuk, A.; Katruk, D.; Kuzioła, R.; Bratychak Jr., M.; Chopyk, N.; Khromyak, U. Influence of Polymer-Silicate Nucleator on the Structure and Properties of Polyamide 6. Chem. Chem. Technol. 2020, 14, 496-503. https://doi.org/10.23939/chcht14.04.496
dc.relation.referencesen[24] Meng, C.; Liu, X. Micro and Macro Analysis of Physicochemical Properties of Bio-Based Semi-Aromatic High Temperature Polyamide PA5T/56. POLYM-PLAST TECH MAT 2022, 61, 1118–1129. https://doi.org/10.1080/25740881.2022.2039186
dc.relation.referencesen[25] Prystynskyi, S.; Budash, Yu.; Plavan, V.; Shuliak, R. Vplyv osnovnykh tekhnolohichnykh parametriv na stabilnist protsesu lyttia pid tyskom multykomponentnykh vidkhodiv polimernykh kompozytsii. Tekhnichni nauky i tekhnolohii 2023, 4, 148–-157. https://doi.org/10.25140/2411-5363-2022-4(30)-148-157
dc.relation.urihttps://doi.org/10.1016/B978-0-12-816808-0.00001-9
dc.relation.urihttps://doi.org/10.1016/B978-012073551-8/50008-8
dc.relation.urihttps://doi.org/10.23939/chcht15.04.543
dc.relation.urihttps://doi.org/10.1007/s10845-019-01481-0
dc.relation.urihttps://doi.org/10.1007/s00170-018-2958-x
dc.relation.urihttps://doi.org/10.3390/ma9080710
dc.relation.urihttps://doi.org/10.4028/www.scientific.net/AMR.468-471.386
dc.relation.urihttps://doi.org/10.3390/polym13152515
dc.relation.urihttps://doi.org/10.1002/app.47257
dc.relation.urihttps://doi.org/10.1002/anie.201805766
dc.relation.urihttps://doi.org/10.1016/j.scitotenv.2020.141228
dc.relation.urihttps://doi.org/10.3390/polym11050912
dc.relation.urihttps://doi.org/10.1021/jacs.0c09293
dc.relation.urihttps://doi.org/10.1016/j.polymer.2014.04.031
dc.relation.urihttps://doi.org/10.23939/chcht15.04.486
dc.relation.urihttps://doi.org/10.3139/217.3058
dc.relation.urihttps://doi.org/10.1088/1742-6596/2051/1/012012
dc.relation.urihttps://doi.org/10.1002/adv.21944
dc.relation.urihttps://doi.org/10.3390/polym14010023
dc.relation.urihttps://doi.org/10.1002/app.51980
dc.relation.urihttps://doi.org/10.1177/0954407020976195
dc.relation.urihttps://doi.org/10.23939/chcht14.04.496
dc.relation.urihttps://doi.org/10.1080/25740881.2022.2039186
dc.relation.urihttps://doi.org/10.25140/2411-5363-2022-4(30)-148-157
dc.rights.holder© Національний університет “Львівська політехніка”, 2023
dc.rights.holder© Prystynskyi S., 2023
dc.subjectлиття пластмас під тиском
dc.subjectпараметри процесу
dc.subjectстабільність процесу
dc.subjectагресивне середовище
dc.subjectхімічна стійкість
dc.subjectполярний розчинник
dc.subjectполіамід
dc.subjectinjection molding
dc.subjectprocess parameters
dc.subjectprocess capability
dc.subjectaggressive environment
dc.subjectchemical resistance
dc.subjectpolar solvent
dc.subjectpolyamide
dc.titleAdjusting the Performance Properties of Products Obtained by Injection Molding from Polyamide 12
dc.title.alternativeРегулювання експлуатаційних властивостей виробів отриманих методом лиття пластмас під тиском з поліаміду 12
dc.typeArticle

Files

Original bundle

Now showing 1 - 2 of 2
Thumbnail Image
Name:
2023v17n4_Prystynskyi_S-Adjusting_the_Performance_836-845.pdf
Size:
1.18 MB
Format:
Adobe Portable Document Format
Download
Thumbnail Image
Name:
2023v17n4_Prystynskyi_S-Adjusting_the_Performance_836-845__COVER.png
Size:
558.63 KB
Format:
Portable Network Graphics
Download

License bundle

Now showing 1 - 1 of 1
Thumbnail Image
Name:
license.txt
Size:
1.75 KB
Format:
Plain Text
Description:
Download

Collections

Chemistry & Chemical Technology. – 2023. – Vol. 17, No. 4